Candy Refrigerator Error E1
⚡ Quick Answer: The Candy refrigerator E1 error indicates a malfunction in the temperature sensor, specifically the NTC sensor in the refrigerator compartment. This c... ✅ DIY Fixable
What Does Error E1 Mean?
The Candy refrigerator E1 error indicates a malfunction in the temperature sensor, specifically the NTC sensor in the refrigerator compartment. This can lead to inaccurate temperature readings and cause the refrigerator to run continuously, resulting in insufficient cooling and potential food spoilage. The issue may stem from an open circuit, shorted sensor wiring, or less commonly, a failure in the main control board.
Common Symptoms:
- Temperature display shows E1
- Refrigerator compartment too warm
- Compressor runs frequently or continuously
- Inability to maintain set temperature
Possible Causes
- Refrigerator compartment NTC temperature sensor open circuit or shorted (medium)
- Damaged or loose sensor wiring harness or connector (medium)
- Main control board temperature input failure (less common) (low)
How to Fix Error E1
DIY Fix Basic checks and reset
- Unplug the refrigerator from mains power and wait 5–10 minutes
- Plug it back in and observe if E1 clears
- Ensure fridge vents inside are not blocked by items
Technician Only Inspect and replace temperature sensor and wiring
- Disconnect power and remove interior panels to access fridge compartment NTC sensor
- Visually inspect sensor and wiring harness for damage or loose connectors
- Use a multimeter to test NTC sensor resistance at room temperature (expected approximate range per model specification)
- Replace sensor if open or shorted, or repair wiring harness
- Verify connector seating at the main control board
Parts needed: Refrigerator compartment NTC temperature sensor, Sensor wiring harness, Connectors
- If sensor replacement and wiring inspection do not clear E1
- If control board shows signs of damage or fault persists after basic diagnosis
Next step
Choose the next step for E1
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Refrigerator parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Refrigerator Condenser Coil Brush
For routine cleaning of accessible condenser areas where the manufacturer permits it. It does not repair a sealed-system or compressor fault.
Model-Compatible Refrigerator Water Filter
A routine replacement item on models with a water filter. Match the complete appliance model and existing filter number before ordering.
Compatibility check required: use the complete appliance model and compare the existing filter, bag, or specification before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | |
|---|---|
| component | Temperature Sensor |
| resistance | 5-10 kOhms |
| part_number | CANDY 41021045 |
| voltage_rating | 120V AC |
Common Questions
What does E1 error mean on Candy refrigerator?
E1 indicates a malfunction in the temperature sensor, causing incorrect temperature readings.
Can I fix Candy refrigerator E1 error myself?
Yes, start with basic checks: unplug the fridge, wait, and check for blocked vents.
How much does it cost to fix E1 error?
The estimated repair cost ranges from $30 to $150 for parts like the sensor and wiring.
When should I call a technician for E1?
Call a technician if sensor replacement doesn't resolve the issue or if the control board shows damage.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!