Blomberg Dishwasher Error E6
⚡ Quick Answer: The Blomberg Dishwasher E6 error indicates a water level detection malfunction, causing the dishwasher to stop mid-cycle or fail to start. This issue ... ✅ DIY Fixable
What Does Error E6 Mean?
The Blomberg Dishwasher E6 error indicates a water level detection malfunction, causing the dishwasher to stop mid-cycle or fail to start. This issue often results in improper filling or draining, typically due to a faulty water level sensor or a misread water level. Users may notice unusual noises during operation, signaling a problem with the drain pump or water level management.
Common Symptoms:
- Dishwasher stops mid-cycle or fails to start
- Error code display upon start or during wash
- Dishwasher may not fill or drain properly if water level monitoring is disrupted
Possible Causes
- Faulty water level sensor/float or misread water level (medium)
How to Fix Error E6
DIY Fix Check filters, correct installation and restart
- Turn off power to the dishwasher.
- Ensure all filters are properly seated and clean any debris.
- Check that there is no excess detergent blocking sensors or filters.
- Restore power and start a short cycle to see if code clears.
Technician Only Inspect and test water level sensor/float assembly
- Disconnect power and water supply.
- Inspect the water level sensor (float switch or pressure sensor) for damage or obstruction.
- Test the sensor/float with a multimeter and verify continuity and correct operation.
- Replace the faulty sensor or associated wiring/harness if needed.
Parts needed: Water level sensor or float switch, Associated wiring harness
- If the error persists after basic user-level checks
- If there are signs of internal leakage or wiring faults during inspection
- If water enters but drain/level detection is inconsistent repeatedly
Next step
Choose the next step for E6
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
- Typical part-only price
- $25 - $65
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 40W |
|---|---|
| component | Drain Pump |
| resistance | 10-15 ohms |
| part_number | BLD-PUMP-001 |
| voltage_rating | 120V AC |
Common Questions
What does E6 error mean on Blomberg Dishwasher?
The E6 error indicates a water level detection malfunction, often causing the dishwasher to stop mid-cycle.
Can I fix Blomberg Dishwasher E6 error myself?
Yes, check filters and ensure proper installation. Restart the dishwasher after cleaning any debris.
How much does it cost to fix E6 error?
Repair costs range from USD 50 to 150 for parts, plus labor depending on service rates.
When should I call a technician for E6?
Call a technician if the error persists after user checks or if there are signs of leakage.
Data last verified: 2026-07-22
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!