AEG Oven Error F03
⚡ Quick Answer: The AEG oven F03 error code indicates a malfunction in the temperature sensor or its circuit, resulting in erratic temperature readings and potential ... ⚠️ Difficulty Varies
What Does Error F03 Mean?
The AEG oven F03 error code indicates a malfunction in the temperature sensor or its circuit, resulting in erratic temperature readings and potential failure to heat properly. This error may appear immediately when powering on the oven or during preheating. If the issue persists after a power reset, it suggests a deeper problem within the temperature sensing circuitry or control communication, necessitating further diagnostics or repair.
Common Symptoms:
- Oven fails to start a cooking cycle
- Error F3 appears on display immediately at power‑on or during preheat
- Oven does not heat or maintains temperature control
- Reset or power cycle does not clear the code
Possible Causes
- Temperature sensor circuit fault (medium)
- Intermittent or failed communication between sensor and control board (medium)
How to Fix Error F03
DIY Fix Perform a power reset and simple checks
- Turn off the oven at the mains or fuse box
- Wait at least 30 seconds and restore power
- Try restarting the oven to see if the error clears again
Technician Only Diagnose temperature sensor and circuit
- Disconnect power to the oven
- Remove access panels to reach the oven’s temperature sensor and wiring
- Inspect sensor wiring and connectors for looseness or damage
- Test the sensor’s resistance with an appropriate multimeter to check for open or incorrect readings
- If sensor or wiring is faulty, replace as needed
- If sensor and wiring check out, evaluate the oven control board’s input circuitry
Parts needed: temperature sensor (RTD/probe), wiring harness, control board
- If the error persists after power reset
- If you are uncomfortable performing electrical diagnostics
- If internal components (sensor/wiring/control board) are suspected faulty
Next step
Choose the next step for F03
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Temperature Sensor |
| resistance | 1000-1100 ohms |
| part_number | AEG 50200146003 |
| voltage_rating | 230V AC |
Common Questions
What does F03 error mean on AEG oven?
F03 indicates a temperature sensor malfunction, causing erratic heating or failure to heat.
Can I fix AEG oven F03 error myself?
Yes, you can perform a power reset by turning off the oven for 30 seconds, but further diagnostics may require a technician.
How much does it cost to fix F03 error?
Repair costs for the F03 error range from $50 to $350, depending on parts needed.
When should I call a technician for F03?
Call a technician if the error persists after a power reset or if you're uncomfortable with electrical diagnostics.
Sources & References
Data last verified: 2026-07-26
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!